Recent Columns by Ray Prasad

• SMT - Unresolved Issues in Lead-free Through-hole Soldering and Surface Finishes  June 2007  Lead Free Magazine
  Since we have been in SMT for more than two decades in high-volume production
  
  Since we have been in SMT for...

• SMT- DFM in a Lead-free World: Part 1  November 2006  SMT Magazine
  Our industry has adapted to and thrived on numerous changes in 25 years — from thru-hole to surface mount; wave...

• SMT- Vapor Phase Soldering: The Comeback Kid  August 2006  SMT Magazine
  Vapor phase soldering (VPS), also known as condensation soldering, has gone through changes in popularity. It was the process of...

• SMT - Lead-free Reflow Profile Development : Part 2  May 2006  SMT Magazine
  As discussed in my February column, to accommodate constraints imposed by large components with high thermal mass requiring higher peak
  temperature...

• SMT - Lead-free Reflow Profile Development: Part 1  February 2006  SMT Magazine
  With tin/lead there has been total industry unanimity about the composition of solder to be used — eutectic solder with...

• SMT BGA Ball Drop in Pb Free: A concern in Lead Free Assemblies: Part 1  November 2005  LeadfreeMagazine.com
  No matter where you stand on the wisdom of lead free directive by the European Union and their numerous followers...

• Three Steps to Improve SMT Yield   December, 2005  Surface Mount Technology (SMT)
  Most companies attempt to achieve higher yield in SMT products through trial and error at considerable expense and frustration. Even...

• SMT - BGA Ball Drop - A Concern in Lead-free Assemblies  October 2005  SMT Magazine
  No matter where you stand on the wisdom of the EU’s leadfree directive, and the numerous followers across the globe...

• SMT- How clean is clean? Well, make up something.  December 2004  SMT Magazine
  There is no other requirement as confusing and muddled in our industry as the definition of cleanliness of an electronics...

• Part 2: How Clean Is Clean? - SMT Assembly Part 2  February, 2005  Surface Mount Technology (SMT)
  As I stated in my December 2004 column, the definition of cleanliness of an electronics assembly board may be...

• Key Considerations in Selective Soldering for SMT  August 2004  SMT Magazine
  If you happen to be in the market for selective soldering systems, there are lots of choices. However, before settling...

• SMT - End of an Era: Moore’s Law  July 2004  
  Two cores are better than one. Why? Intel says so. It has to do with hitting the brick wall in...

• SMT - Outsourcing to India   Feb 2004  SMT Magazine
  I visit India every year for personal reasons, but tend to teach a class or two while I am there....

• BGA Voids and Their Sources in SMT Assemblies  October 2003  SMT Magazine
  Ball grid array (BGA) is widely used because of its inherent advantage in producing overall lower defects. However, one defect...

• Tools and Techniques for Developing SMT Solder Profile   October 2002  SMT Magazine
  The solder profile, also known as thermal profile, is a key variable in the manufacturing process that significantly impacts product...

• One Solder Profile for All SMT Boards -SMT Article  May 2002  SMT Magazine
  The solder profile, also known as thermal profile, is a key variable in the manufacturing process that significantly impacts product...

• SMT - AOI, Test and Repair: Waste of Money?  April 2002  SMT Magazine
  Any money spent on inspection, test and repair is wasted money. It adds only to cost and, hence, adversely impacts...

• BGA Repair in SMT Assemblies  December 2001  SMT Magazine
  All surface mount components, including BGA, require uniform heating of components and boards and a mechanism for accurate component placement....

• Repair and Rework Requirements for SMT Assemblies  November 2001  SMT Magazine
  In my last two columns, (August and September 2001), I discussed the broader issues of surface mount repair as they...

• SMT- Mass Rework? Automated? You must be Kidding!  October 2001  SMT Magazine
  Mass rework? Automated? Why would anyone need to do mass rework? Are they totally new to SMT? Haven’t companies figured...

• SMT - Laser or Hot Air For Surface Mount Repair?  September 2001  SMT Magazine
  Despite all effort put into design, process and material control, there always will be some assemblies that fail to meet...

• SMT - Mass Rework? Automated? You must be Kidding!  August 2001  SMT Magazine
  Mass rework? Automated? Why would anyone need to do mass rework? Are they totally new to SMT? Haven’t companies figured...

• SMT Optoelectronics or Optronics — Promises and Problems  July 2001  SMT Magazine
  The optoelectronics field is so new that no one can even agree on what to call it. Most people refer...

• SMT Packaging Moore’s Law and You  June 2001  SMT Magazine
  Gordon Moore, whose name is synonymous with integrated circuit (IC) technology, retired from the Intel board this May. Dr. Moore...

• Voids in BGAs in SMT Assemblies - SMT Article  May 2001  SMT Magazine
  Ball grid array (BGA) is no longer considered a technology of tomorrow but a technology used today. If you are...

• SMT- AOI System Alternatives  April 2001  SMT Magazine
  Quality control is key to effective competition in the international market. Specific tools such as statistical quality control (SQC), inspection,...

• SMT- Placing an AOI System in the SMT Line   March 2001  SMT Magazine
  There are various inspection and test methods used in the industry. The visual inspection method is the most common and...

• Building SMT Assemblies with Missing Components to Improve Quality and Delivery  February 2001  SMT Magazine
  From the title of this column, you might find it strange that someone with a reasonable understanding of the SMT...

• Selective Automated Laser Assembly of SMT Assemblies  January 2001  SMT Magazine
  Let me first take this rare, rather once in a lifetime, opportunity to wish all of you, the readers of...

• SMT Solder Paste Printing for SMT Part 1  Sept 2000  SMT Magazine
  Part 1 of a 2-part series.
  
  In surface mount assembly reflow soldering, solder paste is used for the connection between surface...

• SMT Solder Paste Printing For SMT Fine-pitch and Through-hole Components Part 2  October 2000  SMT
  Part 2 of a 2-part series.
  
  In last month’s column (“Solder Paste Printing,” September 2000 SMT, p. 28-33), I discussed the...

• SMT - Role of Packaging in Moore's Law    
  I was having a leisurely morning reading my Saturday New York Times not hoping to find any thing that important....